search

Raypak Temp-Tracker Spezifikationen Seite 25

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 32
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
    •
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 24
TempTracker mod+ & TempTracker mod+ Extension Installation Manual 25
BOILER STAGE SETTINGS
Button: STAGE/
The Stage menu offers the capability of adjusting each of the boiler's operation individually.
• In most installations, all active Boiler adjustments are the same, but each can be
congured differently if desired.
• If the Boilers are not set up properly, the TempTracker mod+ operation may appear to be
erratic.
• When STAGE button is depressed, the Boiler A Settings menu will be shown.
• Make all the appropriate settings for Boiler A (See below).
• After completing all the settings for Boiler A (See below), you have the option of copying
these settings to all other Boilers. Everything but the Mode -- Auto/Standby/Manual/Off/
On -- will be copied.
• Then select the Next Stage option from the menu to bring up the Boiler B Settings menu
and make all the settings. Continue until all Boilers have been set.
• If a TempTracker mod+ Extension is connected to the TempTracker mod+, scrolling
through stages using the Next and Prev Stage menu options will scroll through the
TempTracker mod+ Extension stages as well.
ALERT
To be able to change the TempTracker mod+ settings the Program/Run Switch
must be set to Program. The switch is located under the Enclosure Wiring Cover
for security. The Enclosure Wiring Cover can be securely closed using a lock.
----- STAGE A SETTINGS ----
Mode Auto
Ignition % ---
Mode Start % ---
<Prev Stage>
<Next Stage>
Copy Settings
BACK SELECT
BACK SAVE
------- STAGE A MODE --------
Auto
Standby
Manual
Off
On
OD=35 F SYS=98 F
A B C D
95% 50% --- ---
STAGE MENU
-------- COPY SETTINGS -------
From Stage A
to all other stages
BACK COPY
BACK SAVE
------- STAGE A MANUAL ------
75%
[]
ALERT
Remember to set the Mode
for each stage. For Stages
that do not have a boiler,
contractor must change their
Mode to OFF. Otherwise
the TempTracker mod+ will
include them in the modulation
calculation and rotation. That
might have dire effects on
system response.
--------
SYSTEM
A
B
C
D
1
2
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
3
4
5
6
7
8
9
10
11
12
13
15
14
17
16
18
20
19
21
24
23
29
25
27
26
28
32
30
31
L
N
-
+
+
T
T
O
O
RS-485
mA
GND
VLT
SYS
A
B
C
D
PWR
CUR / VLT
A
-
+
+
mA
GND
VLT
-
+
+
mA
GND
VLT
+
+
mA
22
-
GND
VLT
+
mA
TEMP
OUTDOOR
O
O
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
LISTED
99RA
CAUTION
: RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
MODE
Auto,Standby,Manual,Off,On Default:Auto
Button: STAGE/Mode
• The TempTracker mod+ only controls the modulation of Boilers set to Auto or (after a
delay) those set to Standby. None of the other settings is recommended for output Boilers
connected to active units.
• Any Boiler without an active unit connected must be set to Off.
• The following list describes the MODE options:
----- STAGE A SETTINGS ----
Mode Auto
Ignition % ---
Mode Start % ---
<Prev Stage>
<Next Stage>
Copy Settings
BACK SELECT
BACK SAVE
------- STAGE A MODE --------
Auto
Standby
Manual
Off
On
OD=35 F SYS=98 F
A B C D
95% 50% --- ---
STAGE MENU
-------- COPY SETTINGS -------
From Stage A
to all other stages
BACK COPY
BACK SAVE
------- STAGE A MANUAL ------
75%
[]
Auto - The TempTracker mod+ will control the Boiler’s operation to maintain the desired Set Point. Only Boilers set to Auto can
be Lead Boilers.
Standby Standby Boilers can only be activated when all Boilers in Auto have been at 100% modulation for a selectable period of
time. Standby is generally used when you want a specic boiler to be available in extreme load conditions. Note that a
Standby Boiler Cannot be a Lead Boiler.
Manual The Manual Mode should only be used when testing a Boiler. Manual overrides the System Prove input. The exact percent
of modulation for a Boiler can be set with the Manual mode. Once selected, the unit will immediately turn on and modulate
to the selected percentage.
Off Any output Boiler A through D not connected to a physical unit should be set to Off. The Off Mode can also be used to
disable units that are being serviced.
On The On Mode should only be used when testing a Boiler. The On Mode overrides the SYSTEM PROVE input. Once set to
On the Boiler will immediately start ring and modulate to 100%.
Seitenansicht 24
1 2 ... 20 21 22 23 24 25 26 27 28 29 30 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare
Verwandte Produkte und Handbücher für Nein Raypak Temp-Tracker
Nein Raypak Temp-Tracker Spezifikationen   (56 Seiten)
  • Caldera Micrel Steba Hampton Bay Signat
  • Samsung Home-Audio-Sets Nokia Ladegeräte für mobile Geräte Bodum Mixer Kidde Nein Epson Schnittstellenkarten / Adapter
  • Senco PC1195 Clarion DB455MC Samsung GT-S8500 Whirlpool FSCR80410 Sony WM-FX495
  • Samsung SGH-C260 Bedienungsanleitung Sylvania LC155SL8 Bedienungsanleitung Yealink SIP-T21 Bedienungsanleitung Commercial Electric CER4742BZ Bedienerhandbuch Evco EVK411 Bedienungsanleitung