Raypak Temp-Tracker Spezifikationen PDF herunterladen (Seite 15)

TempTracker mod+ & TempTracker mod+ Extension Installation Manual 15

steel and cast iron boilers or boilers with low turndown ratios.

• There are many condensing boilers that run more efciently at lower modulation. If it is more energy efcient to run several units

at lower modulation than one at high, select Parallel. This is typically used on water-tube boilers, low mass boilers, or burners with

high turndown ratios.

PROVE/DOMESTIC HOT WATER (DHW)

Prove,DHWWithoutPriority,DHWWithPriority Default:Prove

Button: MENU/<System Startup>/..../Prove-DHW Sharing

• This setting determines the functionality of Input Terminals 29 and 30.

• When Prove is selected, the TempTracker mod+ will not start any boiler stage unless Prove

terminals are connected. However, it will allow the System relay to function normally.

----------- SETTINGS ------------

Season Winter

Set Point 140 F

BACK SELECT

BACK SAVE

------------- SEASON --------------

Winter

Summer

BACK SAVE

------------ SET POINT ----------

140 F

[ ]

--------- RESET RATIO ----------

1.00 OD=4.00 Sys

1.00 OD=3.00 Sys

1.00 OD=2.00 Sys

1.00 OD=1.50 Sys

1.00 OD=1.25 Sys

1.00 OD=1.00 Sys

1.25 OD=1.00 Sys

1.50 OD=1.00 Sys

2.00 OD=1.00 Sys

3.00 OD=1.00 Sys

4.00 OD=1.00 Sys

BACK SAVE

BACK START

-------- SYSTEM STARTUP ------

(START)

to continue

BACK CONTINUE

------------- WARNING ------------

THESE SETTINGS

CHANGE PRIMARY

SYSTEM FUNCTIONS.

-------- ARE YOU SURE? -------

Yes

---------- SENSOR TYPE ---------

Set Point F

Set Point C

Reset F

Reset C

----- SETBACK/SHUTDOWN -----

Shutdown/Disable

Tstat/Enable

Setback

STARTUP

Reset Ratio

Set Point

BACK SAVE

------- OUTDOOR CUTOFF -------

65 F

[ ]

-------------- OFFSET -------------

+0 F

[ ]

BACK SAVE

--- MINIMUM WATER TEMP ----

140 F

[ ]

BACK SAVE

--- MAXIMUM WATER TEMP ----

220 F

[ ]

Reset Ratio

BACK SAVE

Shutdown or

TStat Input

Setback Input

HISTORIES

--- SYS= 91 F, 10:57Am ---

--- OD= 54 F, 11:36Am ---

------ EMS INPUT MODE -------

Disable

Enable

Reset Options

Set Point

----- EMS 4ma SETPOINT-----

120 F

[ ]

------ EMS 20ma SETPOINT-----

220 F

[ ]

---------- BOOST MODE ---------

30 Minutes

Disabled

BACK SAVE

--------- SENSOR FAULT --------

All Off

All On

BACK SAVE

------- OUTPUT D TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

----- PROVE/DHW SHARING ----

Prove

DHW Priority

DHW No Priority

No Priority (Summer)

BACK SAVE

------ MODULATION MODE ------

Normal

Parallel

BACK SAVE

------- OUTPUT A TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

BACK EXIT

BACK NEXT

BACK SAVE

Enabled

BACK SAVE

------- DHW SETPOINT -------

180 F

[ ]

Disabled

• Using those terminals to connect to an aquastat for a Domestic Hot Water call and selecting any of the DHW options will raise the

calculated water temperature to the DHW Set Point (See next setting).

• However, Domestic Hot Water Priority option de-energizes the SYS relay during domestic hot water calls for a period of one hour.

If after the priority period the DHW did not expire, the SYS relay will energize providing heat to the building and the temperature

target will remain at the DHW Set Point. After the DHW call expires, the set point will drop to satisfy the reset ratio or set point.

• Domestic Hot Water No Priority allows the SYS relay, mostly controlling a primary system pump, to remain energized during a

domestic hot water call (aquastat call on terminals 29 and 30). However, in Summer, Shutdown, No Tstat call for heat, or when

outdoor temperature is above Outdoor Cutoff, a DHW call will energize the SYS relay. After the DHW call terminates, the SYS

relay will continue to run for the System Run-On period before turning off.

• Domestic Hot Water No Priority (Summer) behaves the same as the DHW No Priority. The only difference is that in Summer,

Shutdown, No Tstat call for heat, or when outdoor temperature is above Outdoor Cutoff, a DHW call WILL NOT energize the SYS

relay except for the Run-On delay after the DHW call ends.

DOMESTIC HOT WATER SET POINT

(AVAILABLE WITH ANY OF THE DHW PRIORITY OPTIONS)

Adjustablefrom140ºF/60ºCto200ºF/93ºC Default:180ºF/82ºC

Button: MENU/<System Startup>/..../DHW Set Point

• On a DHW call, the TempTracker mod+ will raise the target to the DHW Set Point until the

DHW call expires.

----------- SETTINGS ------------

Season Winter

Set Point 140 F

BACK SELECT

BACK SAVE

------------- SEASON --------------

Winter

Summer

BACK SAVE

------------ SET POINT ----------

140 F

[ ]

--------- RESET RATIO ----------

1.00 OD=4.00 Sys

1.00 OD=3.00 Sys

1.00 OD=2.00 Sys

1.00 OD=1.50 Sys

1.00 OD=1.25 Sys

1.00 OD=1.00 Sys

1.25 OD=1.00 Sys

1.50 OD=1.00 Sys

2.00 OD=1.00 Sys

3.00 OD=1.00 Sys

4.00 OD=1.00 Sys

BACK SAVE

BACK START

-------- SYSTEM STARTUP ------

(START)

to continue

BACK CONTINUE

------------- WARNING ------------

THESE SETTINGS

CHANGE PRIMARY

SYSTEM FUNCTIONS.

-------- ARE YOU SURE? -------

Yes

---------- SENSOR TYPE ---------

Set Point F

Set Point C

Reset F

Reset C

----- SETBACK/SHUTDOWN -----

Shutdown/Disable

Tstat/Enable

Setback

STARTUP

Reset Ratio

Set Point

BACK SAVE

------- OUTDOOR CUTOFF -------

65 F

[ ]

-------------- OFFSET -------------

+0 F

[ ]

BACK SAVE

--- MINIMUM WATER TEMP ----

140 F

[ ]

BACK SAVE

--- MAXIMUM WATER TEMP ----

220 F

[ ]

Reset Ratio

BACK SAVE

Shutdown or

TStat Input

Setback Input

HISTORIES

--- SYS= 91 F, 10:57Am ---

--- OD= 54 F, 11:36Am ---

------ EMS INPUT MODE -------

Disable

Enable

Reset Options

Set Point

----- EMS 4ma SETPOINT-----

120 F

[ ]

------ EMS 20ma SETPOINT-----

220 F

[ ]

---------- BOOST MODE ---------

30 Minutes

Disabled

BACK SAVE

--------- SENSOR FAULT --------

All Off

All On

BACK SAVE

------- OUTPUT D TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

----- PROVE/DHW SHARING ----

Prove

DHW Priority

DHW No Priority

No Priority (Summer)

BACK SAVE

------ MODULATION MODE ------

Normal

Parallel

BACK SAVE

------- OUTPUT A TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

BACK EXIT

BACK NEXT

BACK SAVE

Enabled

BACK SAVE

------- DHW SETPOINT -------

180 F

[ ]

Disabled

SHUTDOWN/TSTAT/SETBACK MODE

ShutdownInput,TStatInput,SetbackInput Default:ShutdownInput

Button: MENU/<System Startup>/..../Setback\Shutdown

• The TempTracker mod+ has two levels of heat, a Normal/Day and a Setback/Night. The

Normal is good for when buildings are occupied and people are active. The Setback/Night

holds a lower system temperature and is for when buildings are unoccupied or inactive.

----------- SETTINGS ------------

Season Winter

Set Point 140 F

BACK SELECT

BACK SAVE

------------- SEASON --------------

Winter

Summer

BACK SAVE

------------ SET POINT ----------

140 F

[ ]

--------- RESET RATIO ----------

1.00 OD=4.00 Sys

1.00 OD=3.00 Sys

1.00 OD=2.00 Sys

1.00 OD=1.50 Sys

1.00 OD=1.25 Sys

1.00 OD=1.00 Sys

1.25 OD=1.00 Sys

1.50 OD=1.00 Sys

2.00 OD=1.00 Sys

3.00 OD=1.00 Sys

4.00 OD=1.00 Sys

BACK SAVE

BACK START

-------- SYSTEM STARTUP ------

(START)

to continue

BACK CONTINUE

------------- WARNING ------------

THESE SETTINGS

CHANGE PRIMARY

SYSTEM FUNCTIONS.

-------- ARE YOU SURE? -------

Yes

---------- SENSOR TYPE ---------

Set Point F

Set Point C

Reset F

Reset C

----- SETBACK/SHUTDOWN -----

Shutdown/Disable

Tstat/Enable

Setback

STARTUP

Reset Ratio

Set Point

BACK SAVE

------- OUTDOOR CUTOFF -------

65 F

[ ]

-------------- OFFSET -------------

+0 F

[ ]

BACK SAVE

--- MINIMUM WATER TEMP ----

140 F

[ ]

BACK SAVE

--- MAXIMUM WATER TEMP ----

220 F

[ ]

Reset Ratio

BACK SAVE

Shutdown or

TStat Input

Setback Input

HISTORIES

--- SYS= 91 F, 10:57Am ---

--- OD= 54 F, 11:36Am ---

------ EMS INPUT MODE -------

Disable

Enable

Reset Options

Set Point

----- EMS 4ma SETPOINT-----

120 F

[ ]

------ EMS 20ma SETPOINT-----

220 F

[ ]

---------- BOOST MODE ---------

30 Minutes

Disabled

BACK SAVE

--------- SENSOR FAULT --------

All Off

All On

BACK SAVE

------- OUTPUT D TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

----- PROVE/DHW SHARING ----

Prove

DHW Priority

DHW No Priority

No Priority (Summer)

BACK SAVE

------ MODULATION MODE ------

Normal

Parallel

BACK SAVE

------- OUTPUT A TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

BACK EXIT

BACK NEXT

BACK SAVE

Enabled

BACK SAVE

------- DHW SETPOINT -------

180 F

[ ]

Disabled

• When Shutdown or TStat are selected, the Day/Night Schedules will be available in the operating menu. Terminals 31 and 32 will

function as a Shutdown (Turn off boilers when shorted) or TStat (Turn off boilers when opened) of the heat functions. However, a

call for DHW will bring the boilers on.

• When Setback is selected, the External Signal option will switch the TempTracker mod+ to Setback mode when shorted on

terminals 31 and 32. This allows the TempTracker mod+ to be managed by an external device or control to provide setback. No

scheduling or boost menu options will be available with Setback.

----------- SETTINGS ------------

Season Winter

Set Point 140 F

BACK SELECT

BACK SAVE

------------- SEASON --------------

Winter

Summer

BACK SAVE

------------ SET POINT ----------

140 F

[ ]

--------- RESET RATIO ----------

1.00 OD=4.00 Sys

1.00 OD=3.00 Sys

1.00 OD=2.00 Sys

1.00 OD=1.50 Sys

1.00 OD=1.25 Sys

1.00 OD=1.00 Sys

1.25 OD=1.00 Sys

1.50 OD=1.00 Sys

2.00 OD=1.00 Sys

3.00 OD=1.00 Sys

4.00 OD=1.00 Sys

BACK SAVE

BACK START

-------- SYSTEM STARTUP ------

(START)

to continue

BACK CONTINUE

------------- WARNING ------------

THESE SETTINGS

CHANGE PRIMARY

SYSTEM FUNCTIONS.

-------- ARE YOU SURE? -------

Yes

---------- SENSOR TYPE ---------

Set Point F

Set Point C

Reset F

Reset C

----- SETBACK/SHUTDOWN -----

Shutdown/Disable

Tstat/Enable

Setback

STARTUP

Reset Ratio

Set Point

BACK SAVE

------- OUTDOOR CUTOFF -------

65 F

[ ]

-------------- OFFSET -------------

+0 F

[ ]

BACK SAVE

--- MINIMUM WATER TEMP ----

140 F

[ ]

BACK SAVE

--- MAXIMUM WATER TEMP ----

220 F

[ ]

Reset Ratio

BACK SAVE

Shutdown or

TStat Input

Setback Input

HISTORIES

--- SYS= 91 F, 10:57Am ---

--- OD= 54 F, 11:36Am ---

------ EMS INPUT MODE -------

Disable

Enable

Reset Options

Set Point

----- EMS 4ma SETPOINT-----

120 F

[ ]

------ EMS 20ma SETPOINT-----

220 F

[ ]

---------- BOOST MODE ---------

30 Minutes

Disabled

BACK SAVE

--------- SENSOR FAULT --------

All Off

All On

BACK SAVE

------- OUTPUT D TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

----- PROVE/DHW SHARING ----

Prove

DHW Priority

DHW No Priority

No Priority (Summer)

BACK SAVE

------ MODULATION MODE ------

Normal

Parallel

BACK SAVE

------- OUTPUT A TYPE --------

4-20ma

0-10v

0-5v

2-10v

1-5v

BACK SAVE

BACK EXIT

BACK NEXT

BACK SAVE

Enabled

BACK SAVE

------- DHW SETPOINT -------

180 F

[ ]

Disabled

BOOST MODE

(NOT AVAILABLE WITH SETBACK)

30Minutes,Disabled Default:30Minutes

Button: MENU/<System Startup>/..../Boost Mode

• If you do not want a Boost simply select Disabled from the boost menu.

• Boost is only available if Shutdown or Tstat is selected in the previous option.

• The morning Boost is designed to return the building to comfortable ambient temperatures after the cooler Night (Setback) period.

The TempTracker mod+ will accomplish this by running elevated water temperatures (will add Setback setting to calculated water

temperature) for 30 minutes before the start of the Day schedule setting. That is, if the normal day set point at a specic outdoor

was 145˚F and the Setback setting was 20˚F, the boost will raise the system calculated temperature to 165˚F for 30 minutes before

the start of the Day Schedule setting.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Raypak Temp-Tracker Spezifikationen Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Raypak Temp-Tracker