Raypak Temp-Tracker Spezifikationen Seite 16
- Seite / 32
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
16 Raypak, Inc.
SENSOR FAULT
AllOff,AllOn Default:AllOn
Button: MENU/<System Startup>/..../Sensor Fault
The Sensor Fault will determine the operating status of all output stages that are set to Auto
when a sensor reads Short or Open.
----------- SETTINGS ------------
Season Winter
Set Point 140 F
<System Settings>
<Maintenance>
<Histories>
<System Startup>
BACK SELECT
BACK SAVE
------------- SEASON --------------
Winter
Summer
BACK SAVE
------------ SET POINT ----------
140 F
[ ]
--------- RESET RATIO ----------
1.00 OD=4.00 Sys
1.00 OD=3.00 Sys
1.00 OD=2.00 Sys
1.00 OD=1.50 Sys
1.00 OD=1.25 Sys
1.00 OD=1.00 Sys
1.25 OD=1.00 Sys
1.50 OD=1.00 Sys
2.00 OD=1.00 Sys
3.00 OD=1.00 Sys
4.00 OD=1.00 Sys
BACK SAVE
BACK START
-------- SYSTEM STARTUP ------
(START)
to continue
BACK CONTINUE
------------- WARNING ------------
THESE SETTINGS
CHANGE PRIMARY
SYSTEM FUNCTIONS.
-------- ARE YOU SURE? -------
No
Yes
---------- SENSOR TYPE ---------
Set Point F
Set Point C
Reset F
Reset C
----- SETBACK/SHUTDOWN -----
Shutdown/Disable
Tstat/Enable
Setback
STARTUP
Reset Ratio
Set Point
BACK SAVE
------- OUTDOOR CUTOFF -------
65 F
[ ]
-------------- OFFSET -------------
+0 F
[ ]
BACK SAVE
--- MINIMUM WATER TEMP ----
140 F
[ ]
BACK SAVE
--- MAXIMUM WATER TEMP ----
220 F
[ ]
Reset Ratio
BACK SAVE
Shutdown or
TStat Input
Setback Input
HISTORIES
--- SYS= 91 F, 10:57Am ---
--- OD= 54 F, 11:36Am ---
------ EMS INPUT MODE -------
Disable
Enable
Reset Options
Set Point
----- EMS 4ma SETPOINT-----
120 F
[ ]
------ EMS 20ma SETPOINT-----
220 F
[ ]
---------- BOOST MODE ---------
30 Minutes
Disabled
BACK SAVE
--------- SENSOR FAULT --------
All Off
All On
BACK SAVE
------- OUTPUT D TYPE --------
4-20ma
0-10v
0-5v
2-10v
1-5v
BACK SAVE
----- PROVE/DHW SHARING ----
Prove
DHW Priority
DHW No Priority
No Priority (Summer)
BACK SAVE
------ MODULATION MODE ------
Normal
Parallel
BACK SAVE
BACK SAVE
BACK SAVE
------- OUTPUT A TYPE --------
4-20ma
0-10v
0-5v
2-10v
1-5v
BACK SAVE
BACK SAVE
BACK SAVE
BACK EXIT
BACK NEXT
BACK SAVE
BACK SAVE
Enabled
BACK SAVE
------- DHW SETPOINT -------
180 F
[ ]
Disabled
RESET MODE
• When All-On is selected, the TempTracker mod+ will turn all boilers On to a 100% when System reads Short or Open and Outdoor
is below Outdoor Cutoff. When Outdoor reads Short or Open, the TempTracker mod+ will turn all boilers On to a 100%.
• When All-Off is selected, the TempTracker mod+ will turn all boilers Off when either System or Outdoor sensor reads Short or
Open.
SET POINT MODE
• When All-On is selected, the TempTracker mod+ will turn all boilers On to a 100% when the System sensor reads Short or Open.
• When All-Off is selected, the TempTracker mod+ will turn all boilers Off when the System sensor reads Short or Open.
• The Outdoor Sensor Short or Open status will not affect the control operation in Set Point mode.
SETTING THE CONTROL TO FACTORY DEFAULTS
To Reset the TempTracker mod+ control to its original factory defaults, power down the
control. Hold down the two right most buttons while powering the control back up until the
Total Clear Started screen appears. The Display will direct you to the Startup
menu to program the control after the defaults are loaded.
TOTAL CLEAR STARTED
Release buttons
and
Please Wait
NOTE: When resetting the control to original factory defaults all control settings will be overwritten and will no longer exist.
ALERT
Do not turn off power to control until all Startup settings have been made. Otherwise, the next
power-up will be set to many Startup factory settings that might not t your application.
- WARNING 1
- 4 Raypak, Inc 4
- TEMPTRACKER MOD+ OVERVIEW 4
- RESET RATIO/OUTDOOR RESET 5
- 6 Raypak, Inc 6
- INITIAL SETUP 6
- INSTALLATION 7
- 8 Raypak, Inc 8
- OUTDOOR SENSOR INSTALLATION 8
- WIRING THE SENSORS 9
- 10 Raypak, Inc 10
- WIRING THE BOILERS 10
- WIRING TO MODULATING MOTORS 11
- 12 Raypak, Inc 12
- MENU SEQUENCE 12
- SYSTEM SETTINGS1 13
- SYSTEM SETTINGS2 13
- MAINTENANCE 13
- STARTUP SETTINGS 14
- 16 Raypak, Inc 16
- SENSOR FAULT 16
- HISTORIES 16
- OPERATING SETTINGS 17
- 19
- LEAD BOILER ROTATION 19
- PURGE DELAY 19
- 20 Raypak, Inc 20
- LAG DELAY 20
- STANDBY TIME 20
- SYSTEM RUN-ON 20
- LAST STAGE HOLD 21
- DAY/NIGHT SCHEDULES 21
- SOFT-OFF DELAY 23
- OUTPUT TRIM 23
- 24 Raypak, Inc 24
- CONFIGURATION 24
- 26 Raypak, Inc 26
- TROUBLESHOOTING 26
- DIRECT HEATING PIPING DIAGRAM 28
- DIRECT HEATING WIRING DIAGRAM 29
- 30 Raypak, Inc 30
- Raypak, Inc 32
- 2151 Eastman Ave. 32
- Oxnard, CA 93030 32
- PH: (805) 278-5300 32
- FAX: (805) 278-5468 32
Verwandte Produkte und Handbücher für Nein Raypak Temp-Tracker
Nein Raypak Temp-Tracker Spezifikationen
(56 Seiten)
(56 Seiten)
Wolf C48S-2FT36 manuály
Uživatelské manuály a uživatelské příručky pro Rádio Wolf C48S-2FT36.
Poskytujeme 1 manuály pdf Wolf C48S-2FT36 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Tabulka s obsahem
Další produkty a příručky pro Rádio Wolf
| Modely | Typ Dokumentu |
|---|---|
| RT364C |
Uživatelský manuál
Wolf RT364C User Manual,
5 stránky
|
| C36S-2FT24 |
Uživatelský manuál
Wolf C36S-2FT24 User Manual,
2 stránky
|
| C60SC-10 |
Uživatelský manuál
Wolf C60SC-10 User Manual,
2 stránky
|
| Challenger XL CCT-24 |
Uživatelský manuál
Wolf Challenger XL CCT-24 User Manual,
2 stránky
|
| F-39110 |
Uživatelský manuál
Wolf F-39110 User Manual,
2 stránky
|
| C24S-2FT12 |
Uživatelský manuál
Wolf C24S-2FT12 User Manual,
2 stránky
|
| FS-4J-0-24M |
Uživatelský manuál
Wolf FS-4J-0-24M User Manual,
2 stránky
|
| DUAL FUEL RANGES 105 |
Uživatelský manuál
   
Wolf DUAL FUEL RANGES 105 User Manual,
140 stránky
|
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern